Luxury & Precision LP6Ti

Luxury & Precision LP6Ti - LP6Ti

Luxury & Precision LP6Ti 32bit 384Khz HiFi Audiophile Lossless DSD Music Player

LP6Ti requires to be pre-ordered, it takes about 2 weeks to make it ready .

Description

High-performance portable player

4 custom R2R DAC chips

INTEL large industrial grade FPGA

Three types of machine power supply

Level-5 titanium button, face shell

R2R DAC sound

The R2R architecture DAC directly outputs the coded corresponding voltage or current through the principle of resistance voltage division or shunt. R2R DAC sound is more natural than DEL SIGMA DAC.

Process for customizing R2R DAC chip

Thousands of precision low temperature drift resistor networks are connected in parallel. In the later stage, the laser and PVD processes are used to adjust and match after secondary processing.

Advantages of custom R2R DAC chip

Integral and differential nonlinear error stability of plus or minus 1.2LSB. 0.018PPM temperature drift is ten thousandth of the flagship DELTA SIGMA DAC chip. The noise within 7nV root hertz is lower than many low-noise op amps.

Large INTEL industrial grade FPGA

INTEL IFDT special promotion, industrial large-scale FPGA

Seven weapons of FPGA

LP’s IP completes seven functions in one FPGA

1. R2R DAC performance multiplier

2. Digital filter

3. Advanced custom EQ

4. Lossless DSD PCMM conversion

5. Low jitter SPDIF OUT

6. Large bandwidth bridge chip

7. Precision clock source

Digital part power supply, the key to the performance of digital audio such as FPGA

Each digital part is independently powered. The digital audio signal and the power supply related to the clock and output have been subjected to secondary filtering. I2S and SPDIF output-related linear power supply for independent IO power supply, even the input and output banks are also separated.

Analog part power supply decoder, pre-stage, post-stage, separate machine architecture

The first group supplies power to the servo circuit of the DAC and DAC voltage parameter reference, similar to an independent decoder.

The second group provides power for buffering, active low-pass filtering and balanced buffering, similar to independent preamplifiers.

The third group supplies power to the amp circuit. The amp is only responsible for current expansion, which is similar to the independent rear stage, with high output and low noise floor.

Independent power supply to the analog part on the reverse side of the circuit board

Isolate outside the shield, away from noise-sensitive chips such as DAC / op amp, the wiring layout is more relaxed.

Peripheral devices give full play to the potential of sound quality

Large silk capacitors and silver-containing tantalum capacitors. Large size alloy inductor, low internal resistance, high continuous current. The copper shield effectively reduces noise interference.

Lossless EQ greatly improves playability

FPGA computing resources bring near-lossless EQ sound quality. The ten-stage EQ reaches the level of EQ machine. Friendly man-machine interface.

High performance

It is equivalent to the use of 32 pcs of PCM1704UK flagship R2R DAC chips. Under high thrust, the THD of the whole machine is less than 0.00045% 127dB.

Large thrust, multiple gains

The balanced output power of 300 ohm earphones is up to 163 mW, and the THD of 32 ohm earphones is less than 0.0005% under high thrust. The balanced output at high gain is up to 7V, and the single-ended output at low gain is only 0.9V, which is suitable for various earphones and earbuds.

Five-stage titanium case is sturdy and portable

Watch-grade materials and processing technology, high specific strength in metal, non-magnetic, stainless, biophilic.

A good horse with a good saddle and a good machine with a good cable

U75 single crystal copper and silver foil wire base, five grade titanium HD800 pin housing, limestone high stable dielectric constant earphones pin.

Specification

Model: LP6 Ti

Size: 135*69*23mm

Screen: 3.5inch, IPS screen, OGS structure, 480*320 revolution

Body material: level 5 Titanium

Back cover: wood

Master control: 1812C

DAC: 4 high linearity, industrial grade R2R DAC

Crystal Oscillator: low phase noise -160dB active crystal oscillator

Coprocessor: INTEL massive FPGA

Power management chip: 1812P+

PCB: 6 lays 43U zedoary matte black

Inductance: low internal resistance high current metal alloy inductor

Analog circuit filter capacitors: silver-containing military tantalum capacitors, large silk capacitors

Capacity: 64GB 24 Bit ECC FLASH

Extend capacity: 256GB micro SD card (TF)

Charger: DC input voltage range 4.8-5.5V, power adapter output voltage suggest to use 2A and above.(compatible with quick charger)

Battery type: lithium battery

Life time: 8 hours (off screen, normal volume playback of non-high bit rate files, single-ended output)

Set up parameters

Suit for earphones impedance: 8-1000ohm

EQ adjustment: 6 styles adjustment and custom EQ

HP output: 3 models adjustment

DoP SPDDIF: support

Digital filter: multiple filtering modes

Output phase setting: 0-180°

USB connect: MSC mode/audio mode

USB DAC: support

USB Audio delay setting: long delay mode/short delay mode

USB power supply setting: USB power supply mode/self power supply mode

DSD decode setting: Native DSD mode/DSD to PCM mode(to adapt to decoders that only support D2P)

Performance parameters of line output

Distortion + noise: 0.0004%

Signal to noise ratio: 126.5dB (single-ended)

Frequency response: 20Hz-20kHz ± -0.5dB

Channel separation: 98dB 10k load

Line output level: 3.5Vrms / 1.8Vrms / 0.9Vrms switchable design

Headphone output part performance parameters (6.3mm single-ended output)

Output power @ 16ohm, 600mW (distortion rate <0.001% of load power)

Output power @ 32ohm, 320mW (distortion rate> 0.0006% of on-load power)

Output power @ 300ohm, 40mW (distortion rate 0.00045% of on-load power)

Frequency response: 20Hz-20kHz ± -0.5dB

Signal to noise ratio: 126dB

Output impedance: 2.2 ohms

Channel separation: 75dB 32 ohm load

Distortion + noise: 0.00045%

Output voltage: 3.5Vrms

Maximum output current: 300mA 8 ohm

Headphone output part performance parameters (4.4mm balanced output)

Output power @ 32ohm, 800mW (distortion rate <0.0005% of load power)

Output power @ 100ohm, 490mW (distortion rate> 0.00045% of on-load power)

Output power @ 300ohm, 163mW (distortion rate 0.00045% of on-load power)

Frequency response: 20Hz-20kHz ± -0.5dB

Signal to noise ratio: 126dB

Output impedance: 4.4 ohms

Channel separation: 113dB 32 ohm load

Distortion + noise: 0.0016%

Output voltage: 7Vrms

Maximum output current: 300mA 8 ohm

Output power description: LP insists on publishing meaningful output power with actual load and distortion rate of about 0.001%. Although our amp has a perfect overcurrent protection function, we do not recommend exceeding or exceeding the criticality of the output power we announced. The value used, especially some low-resistance earphones, excessive volume may damage hearing.

Support audio format: APE / AAC / ALAC / FLAC / WAV / MP3 / WMA / DFF / DSF / AIFF / SACD-ISO

Audio interface: 6.35mm headphone jack X 1, 3.5mm line output (LO) jack X 1, 4.4mm balanced headphone jack X 1, USB-TYPE C jack (data mode / USB DAC mode) X 1

Package

LP6 Ti

6.35mm adapter

USB-TYPE C cable

Protective film

Leather case

Shipping

Will be shipped via DHL/UPS/EMS/FEDEX .

 It is required to put your phone number on the parcel, please leave me your contact number when you pay.


Write a review

Note: HTML is not translated!
    Bad           Good

Due to the impact of the COVID-19 pandemic, global international shipping will delays. The delay at our Hong Kong post office is very serious, so we have changed to other fastest or most efficient international shipping. Now the normal estimated delivery time may be delayed by about 1-2 weeks. In some countries where is higher free-tax rate, we will provide free courier service as much as possible.

Free Shipping

All listed items will be shipped though Registered Airmail with tracking number if there is no extra shipping method option listed or shipping description in the product page.

Economy shipping: Will be shipped without tracking number.

Registered Airmail : Will be shipped via such as Hong Kong post , Deutsche Post , Netherlands Post , Singapore Post, you can leave us a message if you have any requirement about the shipping method .

It will be shipped via Hong Kong Post by default, Europe countries can choose to be shipped via Deutsche Post or Netherlands Post, it is also FREE, pls leave us a message if needed.

Express service: Will be shipped via DHL/EMS/UPS/FedEx

  • $5,790.00

Tags: Luxury & Precision LP6Ti